DRUMMERWORLD OFFICIAL DISCUSSION FORUM   

Go Back   DRUMMERWORLD OFFICIAL DISCUSSION FORUM > Drum Gear > Other Gear

Other Gear Discuss Hardware and all other equipment not covered in the other topics

Reply
 
Thread Tools
  #1  
Old 02-29-2008, 04:47 PM
hwy145 hwy145 is offline
Senior Member
 
Join Date: Jun 2007
Posts: 142
Default Does the Axis Universal Driveshaft have an adaptor for Pearls?

Pearl has that round with one flat side goofy insert for their pedals, and I was wondering if among Axis' adaptors there was one to fit Pearl pedals.

Thanks,
D
Reply With Quote
  #2  
Old 02-29-2008, 05:09 PM
sticksnstonesrus's Avatar
sticksnstonesrus sticksnstonesrus is offline
Silver Member
 
Join Date: Dec 2006
Location: Virignia Beach, Virginia
Posts: 762
Default Re: Does the Axis Universal Driveshaft have an adaptor for Pearls?

I seriously doubt it.

Why would Axis support making a competitors pedal work with their equipment?
Reply With Quote
  #3  
Old 02-29-2008, 05:16 PM
hwy145 hwy145 is offline
Senior Member
 
Join Date: Jun 2007
Posts: 142
Default Re: Does the Axis Universal Driveshaft have an adaptor for Pearls?

Why would they advertise adaptors to fit most pedals?
Reply With Quote
  #4  
Old 02-29-2008, 07:52 PM
sticksnstonesrus's Avatar
sticksnstonesrus sticksnstonesrus is offline
Silver Member
 
Join Date: Dec 2006
Location: Virignia Beach, Virginia
Posts: 762
Default Re: Does the Axis Universal Driveshaft have an adaptor for Pearls?

???


...it also says "call for details". (310) 549-1171.
Reply With Quote
  #5  
Old 02-29-2008, 08:43 PM
hwy145 hwy145 is offline
Senior Member
 
Join Date: Jun 2007
Posts: 142
Default Re: Does the Axis Universal Driveshaft have an adaptor for Pearls?

I did call, and I was met with a non-human answering system. I was hoping I could get help here. So could you please stay out of my thread unless you actually have something to contribute? I need a simple answer- Yes or No.

And by the way, since you're feeling so smug/ smart, since when is it bad business practice for a company to have parts that fit other companies' equipment? One may not spend $700 on a pedal system from Axis, but one might be compelled to spend $100 for a really good driveshaft from said company to fit one's own pedal. It would seem an unwise business practice to cut off that potential market.
Reply With Quote
  #6  
Old 02-29-2008, 09:23 PM
Les Ismore's Avatar
Les Ismore Les Ismore is offline
Platinum Member
 
Join Date: Jul 2006
Location: Location, Location!
Posts: 3,433
Default Re: Does the Axis Universal Driveshaft have an adaptor for Pearls?

[QUOTE=hwy145;414829]I did call, and I was met with a non-human answering system. I was hoping I could get help here. So could you please stay out of my thread unless you actually have something to contribute? I need a simple answer- Yes or No.

And by the way, since you're feeling so smug/ smart, since when is it bad business practice for a company to have parts that fit other companies' equipment? One may not spend $700 on a pedal system from Axis, but one might be compelled to spend $100 for a really good driveshaft from said company to fit one's own pedal. It would seem an unwise business practice to cut off that potential market.[/quote]


Axis UDS will fit all but the weakest/smallest out-put shafts, it'll actually fit thos too.

The hole is 3/8" and round on the newer model UDS, which is what you'd be getting. It will definetly improve your Pearls.

Should the Axis UDS joint's ever become loose, just heat in an oven at 325 degrees for ten minutes, then tighten the screws.

Can't do that with any other drive shaft, once they get loose, you have to play them that way till it gets unbearable, or buy a new shaft.
Attached Images
 

Last edited by Les Ismore; 02-29-2008 at 09:41 PM.
Reply With Quote
  #7  
Old 03-01-2008, 01:42 AM
hwy145 hwy145 is offline
Senior Member
 
Join Date: Jun 2007
Posts: 142
Default Re: Does the Axis Universal Driveshaft have an adaptor for Pearls?

Hey buddy, I was looking for an answer to my question, not the Community College Marketing opinion of Axis' business practice. Talk about stealing the spotlight. Les ismore told me exactly what I needed to hear without opinion or "his take" on my question. I wouldn't have even responded back to this thread if I'd gotten my question answered immediately. Instead, some joker like you has to put his stamp on MY thread by adding useless drivel. Who needs the attention? Thanks again to Les ismore.
Reply With Quote
  #8  
Old 03-01-2008, 01:46 AM
sticksnstonesrus's Avatar
sticksnstonesrus sticksnstonesrus is offline
Silver Member
 
Join Date: Dec 2006
Location: Virignia Beach, Virginia
Posts: 762
Default Re: Does the Axis Universal Driveshaft have an adaptor for Pearls?

Well, welcome to the wonderful world of forums. Here, the answers might not be immediate...sometimes you never get answers. And yup..there might be some joker out there.

Learn to live.. get over it.
Reply With Quote
Reply


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are Off
[IMG] code is On
HTML code is Off




All times are GMT +2. The time now is 06:35 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Bernhard Castiglioni's DRUMMERWORLD.com